Customers & Feedback

  • "Garmin International"
    A. Landis
  • "Napa Auto Parts"
    J. Isabelle
  • "Resco Plastics, Inc."
    W. Zink
  • "National Aviation Academy"
    J. Cupery
  • "US EPA"
    C. Hankins
  • "Penn State University"
    R. Thomas
  • "City of Raleigh Fire Dept."
    C. Joyner
  • "Empire Floors CA"
    C. Misner
  • "National Air of Texas"
    C. Williams
  • "North Pressure Wash"
    J. Yos
  • "Kilroy Insulation"
    S. Johnson
  • "RSM Electron Power, Inc."
    J. Diaz
  • "Alaska Pacific Rental"
    M. Steel
  • "Springhill Medical Center"
    R. Price
  • "Speedy Concrete Cutting"
    T. Barna
  • "C&W Davis Transport"
    C. Davis
  • "Elliot Electric"
    T. Cox
  • "Wickstrom Ford"
    P. Morgan
  • "All Phase Hydraulics"
    J. Truax
  • "National Magnetics Group, Inc."
    D. Flyte
  • "Dakota Battery & Electric"
    K. Rick
  • "PawPrints Pet Salon"
    P. Falco
  • "LM Heavy Civil Construction"
    P. Frew
  • "Century Mold Company"
    R. Manners
  • "Pentair Water"
    A. Cruz
  • "Speed Wrench Inc."
    T. Decker
Secured Checkout

  Home > Oberdorfer Pumps > FIP (Pump & Motor) >

Oberdorfer FIP Pump w/ Mtr Model# 209ME-A94
Oberdorfer FIP Pump w/ Mtr Model# 209ME-A94
 
List Price: $720.09
Our Price: $514.35
You save $205.74!


Availability: In Stock, Usually Ships in 24 Hours
Product Code: 209ME-A94

Description
 
Oberdorfer FIP Pump w/ Mtr Modle# 209ME-A94

Close-coupled Rubber Impeller Pumps are made of high quality bronze for maximum corrosion resistance.

The rubber impeller is either directly attached to the stainless steel motor shaft or the impeller is mounted on a separate stainless steel shaft, which is counter bored on the outer end in order to slide over the carbon steel motor shaft. Ball or sleeve bearings in the motor support the shaft. Model 406M has a mechanical seal. Impellers are made of Neoprene rubber, Nitrile impellers are available on request. Flexible blades on the periphery of the impeller provide the pumping action. While the impeller rotates, the liquid between the blades is continuously squeezed out into the discharge port by a cam located inside the pumping chamber. The flow may be throttled or shut off for a short period without the need of a relief valve.

FEATURES

  • All Bronze Construction
  • Large Vent Openings Separate Pump and Motor
  • Stainless Steel Motor Shaft
  • Motor Shaft Slinger Protects Motor Bearings
  • Rubber Motor Grommets for Noise Isolation
  • Macerator Wheel and Impeller Easily Replaced
  • Removable Base

PUMP INLET:

2” slip-on hose section with 1 ½” NPT standard pipe male thread. All suction connections must be air tight to achieve lift.

PUMP OUTLET:

3/4” external garden hose thread with 3/8” NPT standard pipe thread internal.

MACERATOR:

Will handle sewage, waste, toilet paper, cigarettes, cigars and all maceratable solids of approximately 1 inch size. Will not handle fruit pits, hard plastic utensils, prophylactics, cloth or fabric sanitary napkins.

MOTOR:

12 volt D.C. high torque, 18 amps. Intermittent duty cycle. Do not run pump dry. 24V and 32V also available.

SUCTION AND DISCHARGE:

Self priming up to 4 ft. Up to 20 ft. uphill discharge or up to 50 ft away. (Use large diameter garden hose- ¾”- for best results.) A 30 gallon holding tank can be emptied in less than 4 minutes.

LIQUIDS & TEMPERATURES

Liquids compatible with neoprene can be pumped including fresh and salt water solutions and mild chemicals. Do not pump severe solvents or acids. When possible, flush pump with fresh water after each usage. Nitrile impellers can handle oil contaminated water and kerosene at reduced impeller service life. Extremes of cold and heat will affect impeller life. Limits of 40° to 140° F should be observed. Do not allow liquid in pump to freeze. Drain pump by loosening cover screws. Use methyl alcohol based anti-freeze compounds such as Zerex, Shell Zone, Pyro Permanent, Permagard, Dowgard.

SUCTION LIFT

Suction lift of 15 feet is possible when pump remains primed (2.5 feet when suction line is empty). Suction lines must be air tight in order for pump to self prime. A foot valve at beginning of suction line is recommended.

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Oberdorfer Pumps > FIP (Pump & Motor)