Customers & Feedback

  • "Garmin International"
    A. Landis
  • "Napa Auto Parts"
    J. Isabelle
  • "Resco Plastics, Inc."
    W. Zink
  • "National Aviation Academy"
    J. Cupery
  • "US EPA"
    C. Hankins
  • "Penn State University"
    R. Thomas
  • "City of Raleigh Fire Dept."
    C. Joyner
  • "Empire Floors CA"
    C. Misner
  • "National Air of Texas"
    C. Williams
  • "North Pressure Wash"
    J. Yos
  • "Kilroy Insulation"
    S. Johnson
  • "RSM Electron Power, Inc."
    J. Diaz
  • "Alaska Pacific Rental"
    M. Steel
  • "Springhill Medical Center"
    R. Price
  • "Speedy Concrete Cutting"
    T. Barna
  • "C&W Davis Transport"
    C. Davis
  • "Elliot Electric"
    T. Cox
  • "Wickstrom Ford"
    P. Morgan
  • "All Phase Hydraulics"
    J. Truax
  • "National Magnetics Group, Inc."
    D. Flyte
  • "Dakota Battery & Electric"
    K. Rick
  • "PawPrints Pet Salon"
    P. Falco
  • "LM Heavy Civil Construction"
    P. Frew
  • "Century Mold Company"
    R. Manners
  • "Pentair Water"
    A. Cruz
  • "Speed Wrench Inc."
    T. Decker
Secured Checkout

  Home > Oberdorfer Pumps > FIP (Pump & Motor) >

Oberdorfer FIP Pump w/ Mtr Model# 406MG-03UGY
Oberdorfer FIP Pump w/ Mtr Model# 406MG-03UGY
 
List Price: $1,928.24
Our Price: $1,377.32
You save $550.92!


Availability: In Stock, Usually Ships in 24 Hours
Product Code: 406MG-03UGY

Description
 
Oberdorfer FIP Pump w/ Mtr Modle# 406MG-03UGY

Close-coupled Rubber Impeller Pumps are made of high quality bronze for maximum corrosion resistance.

The rubber impeller is either directly attached to the stainless steel motor shaft or the impeller is mounted on a separate stainless steel shaft, which is counter bored on the outer end in order to slide over the carbon steel motor shaft. Ball or sleeve bearings in the motor support the shaft. Model 406M has a mechanical seal. Impellers are made of Neoprene rubber, Nitrile impellers are available on request. Flexible blades on the periphery of the impeller provide the pumping action. While the impeller rotates, the liquid between the blades is continuously squeezed out into the discharge port by a cam located inside the pumping chamber. The flow may be throttled or shut off for a short period without the need of a relief valve.

FEATURES

  • All Bronze Construction
  • Stainless Steel Shafts
  • Portable
  • Compact
  • Easy Impeller Replacement
  • Macerator Easily Replaced
  • Reversible Wear Plate
  • Vacuum Switch Shut-off Optional

DRIVE

Close coupled Rubber Impeller Pumps are mounted directly onto the electric motor without the use of a shaft coupling. This pump is coupled to a standard motor with Nema C flange. It uses a bronze adapter plate to accommodate the pump.

LIQUIDS & TEMPERATURES

Liquids handled by Rubber Impeller Pumps with standard Neoprene impellers are primarily fresh or salt water and water solutions. Rubber Impeller Pumps are not suitable for pumping gasoline or solvents. Nitrile impellers can handle oil contaminated water and kerosene at reduced impeller service life.

Liquid temperature range is from 40o F to 180oF. If freezing conditions are expected, the pump should be drained by loosening the cover screws and the pump chamber should be filled with antifreeze. Viscous liquids and oils cannot be pumped with Rubber Impeller Pumps.

SUCTION LIFT

On initial start-up, Rubber Impeller Pumps must be primed to prevent dry-running of the impeller. DO NOT RUN DRY. Suction lifts of 15 ft. are possible when pump is fully primed. A foot valve with built-in strainer at the beginning of the suction line is recommended. Suction lines should be as short as possible.


Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Oberdorfer Pumps > FIP (Pump & Motor)